10 simple steps to reset the VSC light of Toyota and Lexus model

We use affiliate links and may receive a small commission on purchases. Read more about us.

If you are a Toyota or Lexus car user, you probably are a little intrigued about the functionality of the VSC light. Such functionality kinds of give you better controllability over the car.

VSC that stands for Vehicle Stability Control is a type of light included in most Toyota or Lexus cars that help the drivers to get better stability while driving.

VSC is an intelligent system that can detect when your car is losing traction in a tough condition.

In reaction to the realization, the VSC system removes the engine's power to certain wheels to bring forth the best possible stability to your car.

If you are thinking about resetting your Toyota or Lexus car’s VSC light, we are here with the right piece of information so that you can reset the VSC light on your own.

Without any further I do, let us jump into the discussion-

Why should you reset your vehicle’s VSC light?

The VSC light controls the stability of your vehicle. Therefore, when you change the tires or any part of your vehicle, the mechanism forces the VSC system to initiate its process.

As a result, you lose the authenticity to cross certain speed limits as the vehicle thinks that you are losing control and stability over the vehicle.

Resetting the VSC light will allow you to drive the vehicle according to your full potential.

When you are reading this article, you must have come here for the following section, which is the peak topic of this article-

How to reset a Toyota VSC light?

Here are the step by step guidelines to reset your Toyota or Lexus car’s VSC light-

Step one: make sure your vehicle is on a flat surface

Our intention here is to get the zero-point calibration. Therefore, the first thing you need to do is center the steering wheel of the vehicle.

Always ensure that your vehicle is on a flat surface while centering the steering wheel. Once you center the steering wheel and place the vehicle on a flat surface, you need to turn the vehicle.

Well, the preparation is finished for now; let’s jump into the real work now, which has been discussed in the following section-

Step two: locate the OBDII connector.

The next thing you need to do is locate the OBDII connector. Locating the OBD connector can be tough if you do not have any previous experience.

Depending on your Toyota or Lexus car model, the positive will vary. Therefore, we recommend digging a little deeper about your car’s specific OBD connector position to get the job done.

Step three: you will need a paper clip

We are going to do the job in an unconventional way so that you get your job done without facing any sort of inconvenience at all.

Collect a paper clip that we need to connect in two different positions to reset the VSC lights of most Toyota and Lexus lineups.

Step four: making the right connection

Once you have located the OBD connector, you will have to make the right connection to reset the VSC light of your specific model.

On the OBD connector, you will notice that there are two lines of pins. By pins, we are referring to those holes that have electrical wires inside of them.

One line will have more pins than the others. The line that has fewer pins (with electrical wire) is our ideal place to start the work.

You will need to put one part of the paper clip on the fourth one down which is closer to the middle.

And the one directly across from it on the other line is the one you will need to link the paper clip.

Step five: Turn the power on of your vehicle

Once you have made the right connection, you will need to turn the power on of your vehicle.

If you have done everything in the correct way, you should see all the lights on the VSC light indicator flashing simultaneously.

Wait for at least five to ten seconds once you power on the vehicle.

If you have everything right, your vehicle should show that it is in the VSC test mode.

Step six: start the vehicle.

Once your vehicle is in the VSC test mode, you can go ahead and start the vehicle. Once you start the vehicle, let all the lights flash for about five to ten seconds.

This is an important and must-do step. Don’t shut off your vehicle unless the lights flash for about five to ten seconds.

Step seven: shut the vehicle off.

Once the lights have completed the cycle of flashing for about five to ten seconds, you can shut the vehicle off.

Step eight: remove the paper clip you have installed

After shutting off the vehicle, you will have to remove the paper clip you have connected initially on the OBD connector. 

That should be it. You have already completed the process. It is time to find out whether the processes we have implemented here have worked or not-

Step nine: you can start the vehicle again

In this last part of the section, you will need to turn on the vehicle again. If all the previous steps have gone precisely, the VSC light should be off.

That should sum up the thing that you have correctly done it all.  

Step ten: better clarity

If anything that we have discussed in this article looks a little ambiguous or vague to you, consider checking this video to do it with better clarity see on youtube. If you have toyota tunda you have must must some needed parts like Toyota tundra sit cover, Tundra tow mirrors and bed extender.

Final summary

You may not love it when the Vehicle Stability Control System imposes a restriction on your driving, but that is how the system ensures that you stay safe if you really fall into any harsh situations.